Fundamental Plumbing Insights for Installing a Bathtub
Fundamental Plumbing Insights for Installing a Bathtub
Blog Article
We've uncovered this great article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and reckoned it made sense to talk about it with you on this page.
Mounting a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging job. If the old tub is easily easily accessible, the job can move quickly; if you need to open a wall surface to get rid of the old tub and also position the new bath tub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and also embeded in the new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Rather than working with a contractor to take over a halfway-completed job, it is far better to take into consideration employing one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This post will assist you set up a brand-new tub in your washroom if you have actually already bought a new tub and also do not need to change the setup of your previous supply of water pipelines.
Your devices and also material checklist ought to comprise the following:
Preparing for the Setup
First of all, the supporting frame provided with the bath ought to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Before going on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, position the tub in the required placement. The wooden boards are handy in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bathtub till the level checks out level.
To set up faucets, fit the bottom of the outermost versatile tap adapter to the appropriate supply pipe by making a compression join; after that do the exact same for the various other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages as well as tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and sealing around the tub must wait till the bath tub has actually been made use of a minimum of once as this will settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in place between the faucet as well as the sink. Protect the tap in position with the supplier offered backnut. When the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The former kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a rigid seal, triggering the water to permeate the wall surface in between the bath and also the tiling, resulting in complications with dampness and also feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are sold in tubes and also cartridges, as well as are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill the tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealant can break relatively very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly offered on the market. It is suggested to fit the floor tiles using water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that piece of writing was essential. Appreciated our blog posting? Please share it. Let other people check it out. We truly appreciate reading our article about How to Install a Bathtub.
Check Us Out Report this page